EEE PROJECTS

Project code

Title of the Project

Description

IJEE01

Distribution Transformer Monitoring Using GSM Technology

In this we will monitor transformer parameters like current, voltage and temperature, if any of these parameters found abnormal then this systems sends SMS alert to user.

IJEE02

Prepaid Energy Meter with GSM  technology

the GSM technology is used so that the consumer would receive messages about the consumption of power (in watts)  and  if  it  reaches  the  minimum  amount,  it  would  automatically  alert  the  consumer  to  recharge

IJEE03

Bluetooth remote home automation system using android application.

With this we can control home appliances from our android phone. This safe and secure.

IJEE04

Substation monitoring and controlling using GSM

Substation parameters are monitored and it also send alert message when these parameters are abnormal

IJEE05

Low cost wireless sensor network in field operation monitoring of ac motor

The main aim of this project is to monitor the operation conditions of single-phase AC motors

IJEE06

Applied research of the intelligent temperature-controlled speed adjustable motor in radiator fan

In this project the speed of the FAN will be controlled automatically based on current temperature.

IJEE07

Electronic energy meter with instant billing

This paper presents automated billing of energy meter. It is just like postpaid mobile connection. This is useful for billing purpose in electricity board authority.

IJEE08

Remote power on/off control and current measurement for home electric outlets based on a low-power embedded board and ZIGBEE

We can control the home appliances through ZigBee remote and this system will display the power consumed by the loads.

IJEE09

Energy saving project for heating system with ZigBee wireless control network

The main of this project is to develop energy saving heating system using ZigBee wireless technology

IJEE10

Implementation of ZIGBEE-GSM based home security monitoring and remote control system

The main aim of this project is to develop a security and control automation system by which we can control and monitor the status of home appliances

IJEE11

Automation of residential electricity cut off using network based embedded controller

The main aim of this project is to develop the automation system for residential electricity cut off using network based embedded controller

IJEE12

Design of intelligent streetlight monitoring system based on micro controller

The main aim of this project is to design an intelligent streetlight monitoring system for power saving

IJEE13

GSM-based wireless home appliances monitoring & control system

The main aim of this project is to develop a system, which uses Mobile technology that keeps monitoring of the various appliances, and will control the operation of these appliances with respect to the signal sent by the mobile

IJEE14

Real-Time Atomization Of Agricultural Environment for Social Modernization of Indian Agricultural System

The main of this project is to control the agriculture motor using mobile and also to protect the motor

IJEE15

Method of Measuring Power Quality and Development of Monitor Device

The transmission line voltage, current, and power factor, active power and reactive power are measured and displayed on the LCD

IJEE16

A novel technique of ac power control using micro controller based inverter

The main aim of this work is to design a simple low cost AC voltage controller used to 

Control AC loads which doesn’t demand very high precisions

PROJECTS BASED ON AC TO DC CONVERTERS

AD01

Design Of Controlled Dc Voltage Regulator Using Semi Converter With Motor Drive

230v ac is converted in to dc using SCR's and the required firing pulses for the SCR's are given by the microcontroller. Only 2 SCR's and 2 diodes will be there in the converting circuit.

AD02

Design of controlled DC voltage regulator using full wave converter with motor speed control

230v ac is converted in to dc using SCR's and the required firing pulses for the 4 SCR's are given by the microcontroller.

AD03

Design of dual converter using micro controller with lighting load

       PROJECTS BASED ON DC TO DC CONVERTERS

DD01

Design And Implementation Of Multi Phase(Two- Phase) Chopper Using Micro Controller

DD02

Designing of boost converter using micro controller

DD03

Design of two quadrant/buck-boost converter using micro controller

DD04

Design And Development Of Fly Back Converter With Lighting Load Using Micro Controller

DD05

Design Of Simple Buck Converter With Variable Output Voltage Using PWM IC 3525

DD06

Implementation Of  Enhanced Buck Converter Using Micro Controller With Variable Output Voltage

DD07

speed control of dc motor using four quadrant chopper

DD08

Design of  controlled DC voltage regulator using half controlled converter

       PROJECTS BASED ON (DC TO AC) INVERTERS

INV01

Design of 5 level cascaded multi level inverter with 1 auxiliary switch

INV02

Design Of Single Phase PWM H-Bridge Inverter Using 3525 IC For Variable Output Voltage

INV03

A New Switching Topology In Designing Combined Cascaded Multi Level Inverter(7 Level)  With Reduced THD

INV04

Design Of Full Bridge Inverter With Sine Wave PWM Technique Using Micro Controller For Motor Application

INV05

Design of 5 level symmetrical cascaded multi level inverter

INV06

Single Phase H-Bridge Inverter With Pulse Width Modulation To Reduce Harmonic Content In The Output Voltage

INV07

Design Of 7 Level Asymmetrical Cascaded Multi Level Inverter With Reduced Total Harmonic Distortion

INV08

Design Of Single Phase Parallel Inverter Employing PWM Technology Using Microcontroller

INV09

Single phase  PWM half -bridge inverter using micro controller  with lighting load

INV10

Single phase  PWM half-bridge inverter using 3525 IC with lighting load

PROJECTS BASED ON AC TO AC CONVERTERS

AC1

Design of step down cyclo converter using dual converter SCR bridge with lighting load

PROJECTS BASED ON MOTOR CONTROLLERS

MTC01

A Simplified V/F Control Technique For Speed Control Of Induction Motor

MTC02

Speed Control Of Dc Motor Using Four Quadrant Chopper

MTC03

A Novel Solution In Achieving Variable Speed Control Of Dc Motor Using micro controller

MTC04

Speed Control Of Induction Motor Using Voltage Control Method

MTC05

Employing Frequency Control Technique For Obtaining Variable Speeds In Driving Single-Phase Induction Motor

MTC06

Variable Speed Control Of Universal Motor Using Micro Controller

         PROJECTS BASED ON POWER SYSTEMS

PS01

Transmission Line Multiple Fault Detection And Indication To Substation Using Wireless Technology

Ensuring reliable supply to customers is major point in distributing power. In this project complete protection against such faults are monitored & if any fault occurs, it indicates to nearby substation through RF technology.

PS02

Automatic power factor correction using switching capacitors

In this power factor correction unit it consists of a number of capacitors that are switched by means of relays. These contactors/relays are controlled by a regulator that measures power factor in an electrical network. Depending on the load and power factor of the network, the power factor controller will switch the necessary blocks of capacitors in steps to make sure the power factor stays above a selected value.

PS03

Unbalanced Three-phase Optimal Power Flow for Smart Grids

Whenever a three phase load is unbalanced it will correct the load by switching some of the single phase loads to the other phases.

PS04

Substation monitoring system (measurement of PF, voltage, current, temp.)

PS05

Transformer oil temperature monitoring with automatic Circuit Breaker operation.

The temperature of the transformer oil is monitored and displayed on the LCD. When the temperature increases we will switch ON cooling FAN. Even after switching the FAN if the temperature is not decreased then we will switch of the transformer by using a relay. Bulb is connected as a load.

PS06

Single phasing preventer for protection of three phase (3-ph) loads

All the three phase induction motors need the power supply in all the three phases when it is running if any of the phases is having a power outage then the motor is switched off by using relay and the fault phase is displayed on the LCD so that problem can be solved easily

PS07

Automatic switching of consumer connection in distribution feeder for different load distribution

In the distribution feeder if the single phase consumer loads and unbalancing a three phase system then the consumers are switched to other phases so that the overall three phase system will remain in balanced condition

PS08

Automatic change over for three phase connection with data logger

Whenever a three phase load is unbalanced it will correct the load by switching some of the single phase loads to the other phases and the status of all the loads is shown on the display.

PS09

Automatic switching of consumer connection in distribution feeder for different load distribution

.

PS10

Single phasing preventer for protection of three phase (3-ph) loads

.

PS11

Auto selection of any available phase in 3 phase supply system

When a single phase load is connected to a phase which is having a power outage then the load is automatically switched to another phase by using relays so that the availability of the single phase from the three phases will be more.

PS12

An On-line Monitoring System of Transmission Line Conductor

PS13

Over voltage or under voltage tripping mechanism

                 PROJECTS BASED ON SOLAR POWER

SL01

Solar based sinusoidal PWM inverter using parallel inverter

SL02

Implementation Of Solar Based Full Bridge Inverter With PWM Technique

SL03

Solar based off grid parallel inverter Design using ic 3524

SL04

Solar based energy backup system using micro controller

SL05

Solar based irrigation pumping system for rural agriculture applications

SL06

Distribution grid transformers monitoring using GSM with forced cooling control

SL07

To Design High Efficient Traffic Lights Control System Utilizing Solar Energy

SL08

To Design Accurate Wireless Load Measuring Meter For Power Lines

SL09

Wireless motor starter with acknowledgement using solar energy for agricultural application

SL10

Solar pv cell tracking system for obtaining maximum power output

            PROJECTS BASED ON APPLICATIONS

AS01

Smart Remote for controlling electrical appliance through android mobile.

With this we can control any electrical appliances with our android phone, no need of another remote .It is safe and secure also.

AS02

Virtual nurse- controlling wheel chair through android mobile

With this the patient can easily control his wheel chair through simple and smart touching of android mobile

AS07

Smart Home/office automation through android mobile.

With this we can control any electrical appliances in home or office or industry with our android phone, no need of another remote .It is safe and secure also.

AS09

Smart regulator for controlling fan speed through Android mobile.

With this we can control speed of fan or AC from our android mobile.

AS10

AC motor speed controller through Android mobile.

With this we can control speed of AC motor  from our android mobile

AS11

Advanced street light controlling system through smart phone.

In this we can control street light from anywhere through smart phone.

AS13

Industry/home/office automation through smart phone.

With this project we can control any electrical appliances of office or home or industry from anywhere by using Smart phone.

AS14

Industrial parameters monitoring system through Smartphone

We can monitor different parameters like temperature, voltage, etc through online using smart phone from anywhere

VP08

Home /office/industry electrical appliances controlling by phone call and confirmation through voice feedback.

In this we will switch off and switch on any electrical appliances just by calling to this system and press some buttons using DTMF technology. This system also sends voice feedback of device status that is whether device is on or off.

VP12

Substation monitoring and controlling system with voice alerts.

This system monitor the different parameters of substation like voltage, current and temperature and gives respective voice alerts when something goes abnormal condition and takes necessary action.

FS01

Standalone data logger in SD/MMC card with time stamp for industrial applications.

In this we will monitor and store different parameters in industry like temperature, voltage, etc .We will store these parameters values in SD card along with measured time and date also. The stored data format will be in .txt file or excel format so that we can go through entire monthly data using system.

FS05

Advanced embedded system based a paperless feedback system for colleges and event management systems

As we know to save our world we have to reduce usage of paper. This project helps in eliminate papers used in feedback systems. In this the feedback and suggestions should be entered from key board and this data will be stored in memory card in a file format using ARM7 micro controller.

ET01

Industry parameters monitoring and controlling system based on embedded web server.

In this we will monitor industry parameters like current, voltage, temperature, etc through  online using internet from anywhere in the world and we can also control electrical appliances from internet.

ET03

Zigbee and internet based advanced street light controlling system.

With the help of internet and Zigbee technology we can reduce man power in street light controlling process. We can control street lights from online itself.

ET05

Internet based home/office automation.

With this system we can control any electrical appliances of home or office from anywhere in the world using internet.

EE01

Wireless Scrutinizer for Detecting the fault in Power System.

We take a 230v supply voltage and measure the current in it. Fault condition is created by using bulbs. We measure the input and output current of the load using 2 ct's. When the bulb is on we assume fault is created and it is indicated in another section using rf.

EE02

Wireless load measuring meter for power line.

The power in the transmission line is calculated by measuring voltage, current, power factor, and this is indicated in the display by sending the data wirelessly.

EE03

Up-to-date Recording System of Power Line Losses.

The power loss in the transmission line is calculated by measuring the voltage drop in the line. The voltage drop is created by using a resistor and an inductor.

EE04

Underground cable fault identification.

.

The objective of this project is to determine the distance of underground cable fault from base station in kilometers

EE05

Two quadrant chopper drive for DC motor speed control.

This can be done for small dc motor as well for big (around half hp) motors also depends upon motor availability.

EE06

Wireless motor starter with acknowledgement using solar energy for agricultural application

This system sends a message to user when power comes an also sends information whenever power is absent. This system works with solar energy

EE07

Four quadrant chopper drive for DC motor speed control

This can be done for small dc motor as well for big (around half hp) motors also depends upon motor availability

EE08

design of closed loop controlled DC voltage regulator using full wave  semi- converter

the 230v ac is converted in to dc using SCRs and the output voltage is measured by the ADC and the firing angle of the SCRs is controlled by the microcontroller only 2 SCRs and 2 diodes will be there is converting circuit

EE09

Automatic power factor correction using switching capacitors.

The power factor is measured by using zero crossing detectors and it is corrected by connecting the capacitors using TRIACs or relays.

EE10

Automatic power factor correction using static VAR compensators.

The power factor is measured by using zero crossing detectors and it is corrected by connecting a single capacitor of larger value using TRIAC and by controlling the firing angle.

EE11

Design of closed loop controlled DC voltage regulator using full wave converter.

The 230v ac is converted in to dc using SCRs and the output voltage is measured by the ADC and the firing angle of the SCRs is controlled by the microcontroller only 4 SCRs will be there in converting circuit.

EE12

Three phase load protector with automatic fault indication using micro processor.

Whenever a three phase fault is occurred it will be indicated by using OP-AMPS and by measuring voltages and currents. And the type of fault is indicated in the display.

EE13

Thyristor based soft starter.

The advantage of these starters is the starting current can be controlled to a much lower values than that of the value achieved with the traditional starters.

EE14

Thyristor based star/delta starter.

6 bulbs are used to represent the motor. There are connected to form into 3 pairs with 2 each connected in series. They are connected in star first then in delta to the three phase supply.

EE15

Unbalanced Three-phase Optimal Power Flow for Smart Grids.

Whenever a three phase load is unbalanced it will correct the load by switching some of the single phase loads to the other phases.

EE16

Maximum Demand Controller for Industries.

This system automatically switches off the low priority appliances whenever maximum load power reached.

EE17

Automatic Switching of consumer connection in distribution feeder for efficient load distribution

Whenever a three phase load is unbalanced it will correct the load by switching some of the single phase loads to the other phases.

EE18

Distribution grid transformers monitoring using GSM with forced cooling control system

The data at the distribution transformer is observed using GSM and if there is any fault it will on the cooling fans. If the fault is on current then it will switch off the transformer

EE19

Remote substation monitoring system using bidirectional power line communication.

With the same 230 v power line we can monitor substation parameters.

EE20

Design of closed loop controlled DC voltage regulator using full wave converter through computer.

the 230v ac is converted in to dc using SCR's and the output voltage is measured by the ADC and the firing angle of the SCRs is controlled by the microcontroller only 2 SCRs and 2 diodes will be there is converting circuit. The required output voltage is set by using hyper terminal.

EE21

Design of closed loop controlled ac voltage regulator using TRIAC.

Same as the speed control of ac motor but here output voltage is measured using ADC.

EE22

Transmission line multiple faults detection and indication to electricity board.

Voltage and current faults are detected using differential protection scheme and the type of the fault is transmitted using RF.

EE23

Power theft identification system in distribution lines using differential power measurement.

Current at both the ends of transmission line are measured using CTs and if there is a difference in those currents it means power was theft.

EE24

Automatic transformer shunt and series parameter calculation from open circuit and short circuit test reading.

The OC and SC test readings of the transformer are given through keypad and microcontroller will do calculation and give the output on the LCD.

EE25

Closed loop dc motor speed control.

In this we will control the speed of dc motor and we also take the feedback from the motor and correct the speed level to desired level.

EE26

Design of cyclo converter using micro controller.

The input supply frequency is about 50 Hz. We can get the multiples of 50hz using the SCRs. controller will generate pulses for 4 SCRs and the output frequency of the sine wave is controlled.

EE27

Reverse power protection for generator.

The phase angle of the current and voltage are measured to measure whether the power is in reverse direction of not if the power is in reverse direction then it will switch of the supply.

EE28

Automatic transformer protection using numerical relay.

Difference in currents of the two current transformers' will give a buzzer sound. 

EE29

Automatic phase sequence corrector.

Whenever the RYB phase sequence is changed it will be corrected by using relays.

EE30

Design of earth fault relay.

Whenever there is an internal fault or the earth fault then we can sense that by measuring the magnitude of the current and this will give type of the fault.

EE31

Reactive power compensation using STACOM.

The power factor is measured by using zero crossing detectors and it is corrected by connecting a single capacitor of larger value using TRIAC and by controlling the firing angle.

EE32

Speed control of universal motor using IGBT.

This will be same as the speed control of the ac motor using TRIAC but only difference is IGBT is used to vary the voltage and we will control the dc voltage. First we will convert the 230v ac into dc and then we will control.

EE33

Efficient power saver for street lights using LDR, RTC, LEDs light with solar power

This project saves more power that is being wasted in present street light switching. In this we will consider time and sunlight intensity and we use LED lights and solar power

EE34

Agricultural motor controlling with motor safety and water level indicator using GSM.

The former can control his field motor without need of going to his field just by sending message. This system also provides safety motor from over heat, low phase power and water level indication.

EE35

Automatic changeover for 3 phases connections with data logger.

Whenever a three phase load is unbalanced it will correct the load by switching some of the single phase loads to the other phases.

EE36

Solar Tracking system for Maximum power output with real time power monitoring system.

In this the panel will give maximum power by changing its direction according to sun light direction.

It can be done with two motors arrangement or single motor arrangement

EE37

Voice guider and medicine reminder for patients and old age persons.

In this the user will be given one remote (IR or RF or ZIGBEE), he has to press any button to get what service he wants and that is played from voice IC so that any person can hear it and come to the user. Another feature of this project is to remind the user for medicines.

EE38

Broken conductor detection for overhead lines.

The broken conductor can be sensed by using the voltage drop in the line. We will give three switches to indicate broken condition when the switch is operated it will indicate which switch is operated in terms of kilometers.

EE39

Intelligent shopping trolley using RFID

With this we can save billing time and instantaneously the rate and expiry date of the product will be displayed so that we can do the shopping within our budget.

EE40

Elegant home with power saving, security, safety, remote controlling and auto control of water tank motor

In this we will provide multi features to home like remote controlling of  home appliances ,auto controlling of lights depends upon sunlight and auto controlling of water tank motor when  tank is full and alert the user when intruders come or when gas leakage or fire accident occurs

EE41

Intelligent train engine to avoid accidents and controlling railway gate automatically

In this we will control the train by monitoring the driver’s position or activeness and the gate will b e controlled automatically when train is near the gate.

EE42

Design And Development Of Prepaid Energy Meter  With Serial Data Transmission

In this we have one smart card which contains number units depends upon the amount we will pay. These units will be given to energy meter system to activate and it will supply power to home till that units are consumed and we have recharge same card again.

EE43

Protection And Control Of Low Voltage Motors Used In Industrial Applications.

The motor will be protected from over voltage, current, temperature and ground fault conditions. This system immediately switches off the motor whenever abnormal condition occurs and intimate to control room through RF communication.

EE44

Flexible load sharing of transformer with GSM SMS

It continuously measure the load current and it shares this load with another transformer when the load is more and send an alert through message. The user can also share directly whenever he wants just by sending message

EE45

Agriculture field motor control system using GSM

Motors in the field are controlled with the help of predefined SMS. 

EE46

Industrial Electrical Devices Control System

By this project, we can control the devices in the industries by sending predefined SMS to the controlling unit.

EE47

GSM based DC Motor Speed and Direction Control

The speed and direction of DC motor can be controlled by sending predefined SMS to the system

EE48

Cell Phone based Street Light Controlling System with light failure indication system.

The on and off controls of the street lights can be done using GSM technology. If any light does not work then that information is sent as message to electricity department.

EE49

Temperature Measurement over GSM Mobile

Temperature sensor is used to measure the temperature in a particular room and this measured value is sent through GSM to the user mobile.

EE50

Password protected GSM based Device control.

Controlling the devices from remote places only by authorized persons.

EE51

Fingerprint based Access Control system

Security is provided in restricted areas using fingerprint technology. The persons are asked to give their fingerprint and the system compares this fingerprint with the already stored information in the system and only allows into if it is an authorized one.

EE52

Finger print based elevator (lift) operating system.

Only authorized persons are allowed to access the lift controls.

EE53

Low Cost Wireless Sensor Network In Field Operation Monitoring Of AC Motor.

The motor will be protected from over voltage, current, temperature and ground fault conditions. This system immediately switches off the motor whenever abnormal condition occurs and intimate to control room through RF communication.

EE54

A Zigbee Smart Energy Meter Implementation For Energy Efficient Buildings.

In This system one control system collects the data from different meters in the building and we can control the appliances of each floor through this control system.

EE55

Development of a smart power meter for AMI based Zigbee communication Advanced Metering Infrastructure (AMI).

This will be useful in heavy apartment’s .individual meters data will be collected and maintained by main system .this main system sends collated data to electricity board.

EE56

Remote Power On/Off Control And Current Measurement For Home Electric Outlets Based On A Low-Power Embedded Board And Zigbee Communication

We can control the home appliances through Zigbee remote and this system will display the power consumed by the loads.

EE57

Remote-Controllable and Energy-Saving Room Architecture Based on Zigbee Communication.

In this we can control the loads through Zigbee remote or they will also be controlled automatically to save the power.

EE58

Applications of Short Range Technologies to Industrial Automation: A Zigbee Approach.

Industrial devices are monitored and controlled using Zigbee Technology.

EE59

System for Measuring Power Parameters with Zigbee Connectivity.

This system measures the power from each home and sends to central system which is useful in apartments.

EE60

Wireless Data Encryption and Decryption Using ZigBee

Which used in security applications

EE61

ZigBee Based Automated Irrigation System.

Using ZigBee this system controls the irrigation system automatically.

EE62

Bluetooth Robot with CMOS image sensor(SPY ROBOT)

We can control this robot through Bluetooth from PC and the video sent by robot can be seen in TV or PC

EE63

Remote controlled home automation using Bluetooth

With this we can control home appliances like lights, fan, motor, etc through Bluetooth. This is safe and secured.

EE64

Bluetooth based industrial data acquisition system

This project measures different parameters in industry like voltage, current and temperature and transmit this data to PC continuously through Bluetooth.

EE65

Industrial devices controlling system using Bluetooth

With this we can control industry appliances like machines and motors through Bluetooth. This is safe and secured.

EE66

Intelligent electricity billing system using Bluetooth

This system receives the units consumed from various meters and generates the bill accordingly. This saves the cost, time and manpower.

EE67

Touch screen based smart home automation

We can control the home appliance just by smart touch

EE68

Electrical parameters data logger

In this we will continuously measure and display  electrical parameters like voltage, current, frequency and temperature

EE69

Smart horn for vehicles with alcohol detection for drivers

This system reduces the sound pollution that is generated by unnecessary use of horn. This controls  the horn intensity depends upon vehicle distance and also gives the special sound when object is detected at back side if vehicle moves backside and this system only allows for driving if driver does not consume alcohol

EE70

Smart blind stick with ultra sonic sensor.

This stick gives different sound intensity depends upon the object distance from person or we can play some voice also depends upon distance.

EE71

PIR sensor based power saver for auditorium and conference halls.

This project is used to save the power in conference halls and in auditoriums. When there are no persons in the hall ,then lights and fans will be switched off automatically

EE72

Intelligent security and safety system for colleges and industries

This project detects fire accidents, gas leakages and also alert through SMS  when main door is closed without closing any other room entrance or if any other door is opened without opening main door

EE73

An Efficient Monitoring Of Substations Using Microcontroller using RF

This system monitors the subsystem to provide safety and intimate to control room through RF

EE74

Wireless Power Grid Controller

With this we can control the power grid through PC using RF communication

EE75

RF based industrial Automation System

The industrial loads like motors, coolers, etc are monitored and controlled by a RF remote.

EE76

DC motor speed and direction  control using RF

In this project  we can control speed and direction  of DC motor depending on the requirement  using RF signals

EE77

Wireless Stepper motor control using RF

The stepper motor direction can be controlled using RF communication.

EE78

Power Management System in Hotels using PC.

The various appliances in the hotels are controlled by giving commands from the PC. 

EE79

PC based Hi-tech Home Implementation.

We can control the home appliances just by sitting in front of PC.

EE80

Industrial Automation using PC.

The industrial appliances are controlled by the commands issued from the PC. The controlling unit receives these commands from the PC and controls the devices according to the commands.

EE81

Industrial electrical appliances control using IR.

To reduce the manpower for controlling the devices we are implementing this project. Here we will be controlling devices by using a general TV REMOTE.

EE82

DC motor speed and direction control using IR.

A DC motor is controlled using wireless communication. In this project we can control the speed of the dc motor and its direction.

EE83

Stepper motor control using IR

The direction of the stepper motor can be controlled using an IR remote.

EE84

Automatic Room light controller with visitor counter using IR.

This project displays the number of persons present in the room and controls the light according to the intensity of daylight.

EE85

Auditorium Controlling System

The lights and fans in auditorium are controlled by IR remote.

EE86

Shopping Malls Security and Power Management System using IR

The design of security and the method of consuming the power in the shopping malls are carried out in this project.

EE87

AC motor speed control using TRIAC

The speed of AC motor can be varied rapidly on and off by TRIAC.

EE88

Phase Sequence Indicator and Controlling System.

The controlling unit continuously whether 3-phase is coming from the line or not so as to run the motors which run only with 3-phase. If 3-phase is not coming, the controlling unit automatically shuts down the system.

EE89

Boiler Monitoring and Control System.

The temperature is measured and controlled for the industrial boilers.

EE90

Involuntary Industrial Power Scheduler using Embedded System.

The power management in the industries can be done effectively using this project.

EE91

Power Saver for Advertisement Hoardings using RTC.

This system switches on the lights only at preprogrammed timings using RTC thus saving the power up to the maximum extent.

EE92

Solar Tracker for acquiring maximum power.

The project aims at designing a system that would sense and follow the position of the sun and rotate the panel in the direction of the sun to obtain maximum power output.

EE93

Water Scheduling for Municipalities

Water supply to different localities is done on time basis. The supply will be automatically cut once the time allotted to that particular locality lapses.

EE94

Electronic Security System for Homes/Industries with auto dialer.

This system provides security to the homes or offices by interfacing sensors with the controlling units. If anything goes wrong, the system automatically dials up to the predefined number and also activates the alert system.

EE95

Energy Saver for Automatic Room Light Controller with Visitor Counter

The system aims at saving the power by switching on/off the light depending upon the sensor output. It also counts the number of persons present in the hall and displays this value on the LCD.